JPDiag Forum Index

JPDiag


 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Hypermotard 796 - PC connection problem

 
Post new topic   Reply to topic    JPDiag Forum Index -> JPDiag -> M3C / Mitsu ecus
Previous topic :: Next topic  
Author Message
Fenics
Map

Offline

Joined: 12 Apr 2018
Posts: 5
Masculin

PostPosted: Thu 12 Apr - 19:18 (2018)    Post subject: Hypermotard 796 - PC connection problem Reply with quote

Hello together and thanks for your work with the ECU's Software.

Lets tell a bit, i got a DTC error but no code was displayed at my bike. So i wanted to check via OBD. (Next Duc store is far away)...
I ordered -> this Interface " https://www.tacklifetools.com/product/product/index/id/199 "
and a patch cable " https://www.amazon.de/Ducati-Multistrada-Pin-Adapter-AutoDia/dp/B077TV3Y8F/ref=sr_1_1?s=automotive&ie=UTF8&qid=1523556401&sr=1-1&keywords=ducati+multistrada+4+pin+adapter+motorrad+plug+adapter+for+software "

I tried to connect in any way to the ECU. but no success... Sad

The M3C9b shows me Engine and Air temp and after a few seconds more "Can't init ELM"

What Baudrate is the best for connection? Flowcontrol on or off, or all basic. No changes???

Do u have any advise?

BTW - i tested the adapter on my car and all works fine and without any lag or connection abort.
(and Melcodiag shows ELM327 v1.5)

ECU is Continental M3C 5WY8691-AAA

THANK you  Smile


Back to top
Publicité






PostPosted: Thu 12 Apr - 19:18 (2018)    Post subject: Publicité

PublicitéSupprimer les publicités ?
Back to top
jpl250rs
Administrateur

Offline

Joined: 05 Jun 2010
Posts: 10,375
Masculin
Bike / Moto: 899

PostPosted: Thu 12 Apr - 19:33 (2018)    Post subject: Hypermotard 796 - PC connection problem Reply with quote

did you try with same speed as you set in melcodiag ?

Back to top
MSN
Fenics
Map

Offline

Joined: 12 Apr 2018
Posts: 5
Masculin

PostPosted: Thu 12 Apr - 20:18 (2018)    Post subject: Hypermotard 796 - PC connection problem Reply with quote

Yes, i tried all possible settings. Melcodiag "freezes" when trying to get "collect some ... Data"
In software version it write "a"... No hardware information or else.


Back to top
Fenics
Map

Offline

Joined: 12 Apr 2018
Posts: 5
Masculin

PostPosted: Thu 12 Apr - 20:42 (2018)    Post subject: Hypermotard 796 - PC connection problem Reply with quote

I did forget to mension, that i have a power commander 5 installed. Does this have any effect for the connection? Shouldn't i assume... Rolling Eyes

Back to top
jpl250rs
Administrateur

Offline

Joined: 05 Jun 2010
Posts: 10,375
Masculin
Bike / Moto: 899

PostPosted: Thu 12 Apr - 21:16 (2018)    Post subject: Hypermotard 796 - PC connection problem Reply with quote

no it don't

Back to top
MSN
Fenics
Map

Offline

Joined: 12 Apr 2018
Posts: 5
Masculin

PostPosted: Thu 19 Apr - 23:01 (2018)    Post subject: Hypermotard 796 - PC connection problem Reply with quote

Hello again,

 i ordered another elm327 and i got a bit further. The blue load bar right of the speed option (baud rate) flickers up after connecting.
After some seconds, the prog say, "the programm may response slow, check can bus connection" i get no software or hardware codes but after some secs
the air and engine temps pop up (-36°C) -_- in spring . well....
The error i was looking for, is gone, so i cant check, if the connection works or not...

Do u know a working android app for the m3c?

Thanks and greetings


Back to top
jpl250rs
Administrateur

Offline

Joined: 05 Jun 2010
Posts: 10,375
Masculin
Bike / Moto: 899

PostPosted: Fri 20 Apr - 08:22 (2018)    Post subject: Hypermotard 796 - PC connection problem Reply with quote

main page main give erroneous values , but other functions are fulling working
dtc,resets and test pages


you can help to debug values on 1st page if you want see it good


Back to top
MSN
Fenics
Map

Offline

Joined: 12 Apr 2018
Posts: 5
Masculin

PostPosted: Fri 20 Apr - 08:38 (2018)    Post subject: Hypermotard 796 - PC connection problem Reply with quote

thank u, i will see what i can find Smile

Do u have any idea, why no information about software or hardware or anything is shown?
Or why my first "better" adapter can't connect? "can't init elm" Question


Back to top
jpl250rs
Administrateur

Offline

Joined: 05 Jun 2010
Posts: 10,375
Masculin
Bike / Moto: 899

PostPosted: Fri 20 Apr - 08:54 (2018)    Post subject: Hypermotard 796 - PC connection problem Reply with quote

i've no idea
probably it gives an unexpected answer
i saw some elm returning a lot of carriage return  , that could lost software because it's wasnot expected


Back to top
MSN
Contenu Sponsorisé






PostPosted: Today at 19:03 (2018)    Post subject: Hypermotard 796 - PC connection problem

Back to top
Display posts from previous:   
Post new topic   Reply to topic    JPDiag Forum Index -> JPDiag -> M3C / Mitsu ecus All times are GMT + 1 Hour
Page 1 of 1

 
Jump to:  

Index | Administration Panel | Create a free forum | Free support forum | Free forums directory | Report a violation | Conditions générales d'utilisation
Powered by phpBB © 2001, 2005 phpBB Group